Products

Control Unit

PRODUCT MAP VIEW
  • Control Unit
  • Inverter
FEATURE
MORE DETAILS
  • Control Unit
  • wound rotor motor Controller(FDA)
FEATURE
This FDA series, Digital AC Primary Voltage Controller developed by HANMI TECHWIN, uses thyristors for the control of a three phase induction motor. The FDA series has been developed and standardized to meet the industrial requirements o...
MORE DETAILS
  • Control Unit
  • Magnet Control Unit(FDR)
FEATURE
FDR-series is a digital lifting mark net controller developed by Hanmi Techwin. Power drive device It is a device to apply constant voltage or current to magnet by Converting 3-phase input power by using SCR (thyristor). It is an essent...
MORE DETAILS
  • Control Unit
  • New Magnet Control Unit(TDR)
FEATURE
TDR-series, as an all-digital type lifting magnet controller developed by HANMI TECHWIN. CO. LTD., is a device which imposes 3 phase AC voltage by converting into DC voltage using a power driving component SCR(thyristor) and controlling...
MORE DETAILS
  • Control Unit
  • Brake Controller(TCBⅡ)
FEATURE
TCBⅡ series developed by HANMI TECHWIN is a type of reducing maintenance problems, the old model has been containing seriously . On its stop condition, the electric power left in magnetic brake coil is fed back into the line and by doin...
MORE DETAILS
  • Control Unit
  • New Brake Controller (TBC-6020A)
FEATURE
The digital magnet operated brake controller developed by HANMI TECHWIN, is widely applicable mechanical brake for motor as main driving power such as cranes, etc. and is installed with motor controller. TBC-6020A controls power thyrist...
MORE DETAILS
  • Control Unit
  • Battery Charger
FEATURE
FDCH series, developed by HANMI TECHWIN, are the digital battery chargers used for charging the storage batteries for emergency power source. Recently, the miniaturization with high performance and switch-over to cordless ones of electro...
MORE DETAILS
  • Control Unit
  • New Battery Charger(TDC-9030)
FEATURE
The all-digital battery charger (BCU) developed by HANMI TECHWIN is a device that charges the battery by making high-speed switching method using 3-phase AC power using IGBT. BCU (Battery Charging Unit) monitors and protects battery sta...
MORE DETAILS
  • Control Unit
  • Battery Status Monitor(TDP-BM)
FEATURE
TDP-BM-100 is the device of emergency monitoring battery status for magnet system. Emergency battery installed 9 to 18 in series due to output voltage; therefore, it is difficult to check each battery status. TDP-BM-100, which is possib...
MORE DETAILS
  • Control Unit
  • Moter Speed Detector
FEATURE
The TFC-7050A is a device that detects the speed by taking the slip frequency on the secondary side 3 of the wire-wound motor as input. The speed detection method is precisely calculated digitally using the MCU after removing the noise...
MORE DETAILS
  • Control Unit
  • Motor Brake Unit
FEATURE
The motor brake unit (TEPB-Series) is one of the motor braking methods for the system that uses the motor as the main power. DC braking method to provide stable performance. It is a controller that converts input single-phase AC voltage...
MORE DETAILS
  • Control Unit
  • Noncontact MC
FEATURE
In the speed control method of a wound-wire induction motor, a secondary resistance control method for controlling a slip (speed) by connecting a resistor from the outside of the secondary side (rotor) and a method for controlling both t...
MORE DETAILS
  • Control Unit
  • Control Panel
FEATURE
MORE DETAILS
  • Control Unit
  • Under Current Detector
FEATURE
TDP-UC Series is under current detector for magnet to detect current from magnet pots of which installed sensor for using feedback voltage at each pot to find various causes of under current and over current during the magnet operation p...
MORE DETAILS
  • Control Unit
  • TSA-002B
FEATURE
Noise and Surge Protection
MORE DETAILS